STIR IT UP WIRELESS FAQ

Frequently Asked Questions

1. How do I setup my Stir It Up Wireless Turntable with a Bluetooth speaker?

      1. Unclip the tonearm and remove the protective foam block from underneath it.
      2. Carefully remove the protective cover from the stylus
      3. Look at the belt underneath the metal platter, the belt is already fitted to the platter so make sure it is not twisted.
        • If it is, the belt must be removed and refitted, or adjusted so that it is flat
      4. With the belt around your finger, place the platter on the base of the turntable and line up the large hole with the spindle. Then gently loop the belt around it.
        • If the belt is fitted correctly, there should be some resistance when you rotate the platter
      5. Place the turntable mat on the platter
      6. Place the balance weight on the end of the tonearm by turning and pushing gently
      7. Adjust the balance weight until he arm floats parallel with the turntable
      8. Rotate the balance weight one full turn. This will make the tone arm balanced.
      9. Adjust the tracking weight on the balance to 2.5 (this is the correct weight for the fitted stylus)
      10. Adjust the anti-skate dial to 2.5
      11. Plug the power cord into the socket on the back of the turntable
      12. Switch on your Bluetooth speaker
      13. Press the Bluetooth button once to turn it on
      14. Press the Bluetooth button again to activate pairing mode
        • When the pairing light is solid, the turntable will be paired
      15. Place a record on the turntable
      16. Shift the dial below the anti-skate dial towards you to start the record
      17. Place the stylus above the record and shift the dial away from you to lower the stylus
      18. Enjoy the music!

2. How do I set up my Stir It Up Wireless Turntable with a speaker using a wired connection?

      1. Unclip the tonearm and remove the protective foam block from underneath it.
      2. Carefully remove the protective cover from the stylus
      3. Look at the belt underneath the metal platter, the belt is already fitted to the platter so make sure it is not twisted.
      4. If it is, the belt must be removed and refitted, or adjusted so that it is flat
      5. With the belt around your finger, place the platter on the base of the turntable and line up the large hole with the spindle. Then gently loop the belt around it.
      6. If the belt is fitted correctly, there should be some resistance when you rotate the platter
      7. Place the turntable mat on the platter
      8. Place the balance weight on the end of the tonearm by turning and pushing gently
      9. Adjust the balance weight until he arms floats parallel with the turntable
      10. Rotate the balance weight one full turn. This will make the tone arm balanced.
      11. Adjust the tracking weight on the balance to 2.5 (this is the correct weight for the fitted stylus)
      12. Adjust the anti-skate dial to 2.5
      13. Plug the power cord into the socket on the back of the turntable
      14. Plug an RCA cable into the back of the turntable and connect it to your desired playback device
        • Alternatively, you can connect a 3.5mm (aux) cord into the “headphone” port on the front of the turntable and connect that to your desired playback device
          • Note: you cannot use both the RCA and 3.5mm (aux) port for playback simultaneously
      15. Place a record on the turntable
      16. Shift the dial below the anti-skate dial towards you and place the stylus above the record to start the record
      17. Shift the dial away from you to lower the stylus
      18. Enjoy the music!

3. What is the correct tracking weight setting for the stylus?

    • The tracking weight should be set to 2.5

4. What is the correct setting for the anti-skate dial?

    • The anti-skate dial should be set to 2.5

5. How do I activate Bluetooth pairing mode?

    1. Press the Bluetooth button once to turn it on
    2. Press the Bluetooth button again to activate pairing mode

6. How do I know if the turntable is paired with a Bluetooth device?

    • When the pairing light goes solid, the turntable is paired with a Bluetooth device

7. How do I start a record?

    • Shift the dial below the “anti-skate” dial towards you

8. How do I stop a record?

    • Shift the dial below the “anti-skate” dial away from you

9. What is the model name of the Stir It Up Wireless turntable?

    • EM-JT002

10. What is the size of the Stir It Up Wireless turntable?

    • 14.72”x14.57"x1.97" (450 x 370 x 50mm)

11. What is the weight of the Stir It Up Wireless turntable?

    • 7.76lbs (3.52kgs)

12. How do I recycle my product?

    • House of Marley believes in respect for the earth, which is why we develop products with upcycled materials. Please contact your local e-waste recycling center for drop-off instructions. Unfortunately, due to the complex assembly of the turntable, they cannot be placed in a standard recycle receptacle